IBM 436854u - System x3200 M2 5U Mini Tower Server User Manual

Set the upper bezel aside. Installing An Adapter 3. Removing the side cover To remove the server side cover, complete the following steps: Installing A Tape Drive 9. The power control button on the device and the power switch on the power supply do not turn off the electrical current supplied to the device. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source.

HP Servers / Storage

Enviar a um amigo

If this amber status LED for a drive is lit, it indicates that the associated hard disk drive has failed. Rear view The following illustration shows the connectors and LEDs on the rear of the server. When this LED is lit, it indicates that there is an active connection on the Ethernet port.

The device also might have more than one power cord. To remove all electrical current from the device, ensure that all power cords are disconnected from the power source. System-board internal connectors The following illustration shows the internal connectors on the system board. System-board optional-device connectors The following illustration shows the system-board and connectors for user-installable optional devices.

System-board jumpers The following illustration shows the jumpers on the system board. There are no changeable switches on the system board.

Before you install optional hardware devices, make sure that the server is working correctly. Start the server, and make sure that the operating system Under Product support, click System x.

Under Popular links, click Software and device drivers. For additional information about tools for updating, managing , and deploying firmware, see the System x and xSeries Tools Center at http: System reliability guidelines To help ensure proper system cooling and system reliability, make sure that the following requirements are met: Handling static-sensitive devices Attention: Static electricity can damage the server and other electronic devices.

To avoid damage, keep static-sensitive devices in their static-protective packages until you are ready to install them.

To reduce the possibility of electrostatic discharge, observe the following precautions: Removing the side cover To remove the server side cover, complete the following steps: Removing the two-piece bezel When you work with some devices, such as drives in bays 1 through 7 or bays 1 through 11 if you have the 2. Carefully pull the two bezel clips on the left side of the upper bezel away from the chassis; then, rotate the upper bezel to the right side of the server to disengage the two right-side tabs from the chassis.

Set the upper bezel aside. For a list of supported optional devices for the server, see http: Double-rank Double-rank Single-rank Single-rank This configuration is the best choice. Static electricity that is released to internal server components when the server is powered-on might cause the server to stop, which might result in the loss of data.

To avoid breaking the retaining clips or damaging the DIMM connectors, open and close the clips gently. Open the retaining clips and, if necessary, remove any existing DIMM. Touch the static-protective package that contains the DIMM to any unpainted metal surface on the server. The server supports 2. If you are installing a drive that contains a laser, observe the following safety precaution.

If you are installing a 5. If you are installing a 3. An optional diskette drive can be installed in bay 3.

Remove the drive retainer clip from the side of the drive cage of bays 1 or 2. Slide the drive retainer clip to the right to remove it from the drive cage; then, snap the drive retainer clip into the screw holes on the side of the drive. EMC shield Tape drive Drive retainer clip The hot-swap SATA models support 3.

Before you install a hot-swap hard disk drive, read the following information: IDs for hot-swap hard disk drives On some models, the hot-swap-drive backplane controls the IDs of the internal hot-swap drive bays. The following table lists the IDs of the hard disk drives and backplane that are connected to one channel in the hot-swap models. In the typical configuration, the standard hard disk drives and backplane are connected to channel A.

Simple-swap hard disk drives are not hot-swappable. Disconnect all power from the server before you remove or install a simple-swap hard disk drive. To install a simple-swap hard disk drive, complete the following steps: Review the following information before you connect power and signal cables to internal drives: Universal adapters are supported in slots 4 and 5 if they are universally keyed. Remove the screw that secures the expansion-slot cover to the chassis.

Store the expansion-slot cover and screw in a safe place for future use. Expansion-slot covers must be installed on all vacant slots. This maintains the electronic emissions standards of the server and ensures proper ventilation of server components. Remove the hard disk drive fan assembly: Disconnect the hard disk drive fan assembly cable from the system board and make a note of where the cable was connected for later installation.

Remove all hard disk drives. Incomplete insertion might cause damage to the system board or the adapter. Lock the side cover. Reconnect the external cables and power cords; then, turn on the attached devices and turn on the server.

Installing a hot-swap power supply The following notes describe the type of power supply that the server supports and other information that you must consider when you install a power supply: To replace a hot-swap power supply, complete the following steps: Disconnect the power cord from the power supply that is to be removed. Installing a security rope clip To help prevent hardware theft, you can add a security rope clip and cable to the server.

After you add the security cable, make sure that it does not interfere with other cables that are connected to the server.

Before you begin, obtain the following items: Install the lower bezel: Insert the two bottom tabs on the lower bezel into the matching holes in the front of the chassis.

Rotate the top of the lower bezel up to the chassis; then, press the blue release tab on the right side of the lower bezel and completely close the lower bezel until it locks securely into place. Reinstalling the side cover If you removed the bezel, reinstall it before you reinstall the side cover. The rear adapter-retention bracket rests against the server side cover.

You might find it easier to lay the server on its side to replace the side cover. To reinstall the side cover, complete the following steps: Connecting the cables Attention: To prevent damage to equipment, connect the power cords last.

If the server cables and connector panel have color-coded connectors, match the color of each cable end with the color of the connector. For example, match a blue cable end to a blue connector on the panel, a red cable end with a red connector, and so on. An optional Tower-to-Rack Kit is needed to convert the server from a tower model to a rack model. You can then install the server in a rack cabinet. Use this CD during the installation of the server to configure basic hardware features, such as a ServeRAID adapter, and to simplify the installation of the operating system.

Select this choice to view the processor information, including the type, speed, and cache size of the microprocessor. Select this choice to set or change an administrator password. Run the diagnostic programs to get more information about the error codes. Web site at http: The actual procedure might vary slightly from that is described in this document. The setup program provides a list of tasks that are required to set up the server model.

From the BMC software, copy the files bmc. From the BMC software, copy the file fsloader. To find updated information about configuring the controller, complete the following steps. The materials at those Web sites are not part of the materials for this IBM product, and use of those Web sites is at your own risk.

IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Maximum internal hard disk drive capacities assume the replacement of any standard hard disk drives and population of all hard disk drive bays with the largest currently supported drives that are available from IBM. The materials at those Web sites are not part of the materials for this IBM product and use of those Web sites is at your own risk.

IBM may use or distribute any of the information you supply in any way it believes appropriate without incurring any obligation to you. Such trademarks may also be registered or common law trademarks in other countries. A current list of IBM trademarks is available on the Web at http: Page of 29 Go. The x Compute Node is an efficient server designed to run a broad range of. IBM Flex System is a new category of computing that integrates multiple server architectures, networking,.

Flex System has full built-in virtualization support of servers, storage, and networking to speed. In addition, it supports open industry standards, such as operating. IBM Flex System is scalable and extendable with. Table of Contents Add to my manuals Add. Summary of Contents for IBM Flex System x Compute Node Page 1 IBM Flex System is a new category of computing that integrates multiple server architectures, networking, storage, and system management capability into a single system that is easy to deploy and manage.

Key Features Key features The IBM Flex System x Compute Node is a high-availability, scalable compute node optimized to support the next-generation microprocessor technology and is ideally suited for medium and large businesses.

Page 5 Figure 3 shows the locations of key components inside the server. Page 15 The server does not support an internal optical drive option.

Page 17 pin PCIe connector. Page 21 An over-temperature condition occurs that was critical enough to shut down the server. Page 27 Web sites.

Comments to this Manuals Your Name. Enter text from picture: By pressing 'print' button you will print only current page. To print the manual completely, please, download it. Don't show me this message again.

IBM & Lenovo Servers / Storage